Power Steering Rack and Pinion for 2006 2007 2008 Ford F-150 Lincoln Mark LT 4WD

For 1998 - 2003 Toyota Sienna Complete Power Steering Rack and Pinion Assembly. For Honda Accord 2003 2004 2005 3.0L V6 Power Steering Rack & Pinion 26-2704 USA.

For 2006 2007 2008 Hummer H3 3.7L 3.5L Power Steering Rack and Pinion Assembly. Selection of optimal car parts. Steering gear, also called steering gear, is the most important part of automobile steering system. Power steering (PAS) or steering assist system helps drivers steer by augmenting steering effort of the steering wheel. Power steering rack and pinion is the most important part for vehicle swerving and security assurance.

It converts the rotational motion of the steering wheel into the linear motion needed to turn the wheels and provides a gear reduction, thus making it easier to turn the wheels. - The steering rack solves abnormal noise and oil leakage problems, ensures that the steering wheel rotation angle is proportional to the tire rotation angle, and reduces the steering wheel's control force when turning, which makes driving safer. - There are two functions this power steering rack and pinion unit can provide.

Firstly, it is able to convert the rotational motion of the steering wheel into the linear motion needed to turn the wheels. Secondly, this unit could make a gear reduction, thus making it easier to turn the wheels. - This vehicle steering rack pinion is made of sturdy steel and aluminum alloy with anti-wear and scratch-proof quality.

We put moderate lubricating oil into this assembly so that it can prevent rust and oxidation. - Along with durable shafts, hydraulic lines, steel clamps, and rubber bellow boots, the steering rack unit is quick and easy to assemble that you don't need any adjustments.

Item Type: Power Steering Rack and Pinion Assembly. Complete Power Steering Rack and Pinion Gear Assembly. 1x Power Rack and Pinion Gear Assembly - 22-279. FORD F-150 2004 - 2008 4WD ONLY. LINCOLN MARK LT 2006 - 2008 4WD ONLY.

FITS 4WD / 4x4 MODELS ONLY. 1pcs (As shown in the figure). High-quality replacement:Power steering rack and pinion.

This part may also be known as:Power steering (PAS) or steering assist system. 100% tested For reliability and performance. Top performance For long service life. Undergone strict tests to ensure reliable performance.

Air Tested to Ensure Reliable Performance. Hydraulically Tested to Ensure Internal By-Pass for Both High and Low Pressures. Road simulated for proper functioning. Simple installation and and long life as a guarantee. Backed by satisfying after-sales service.

In order to ensure the normal operation of the steering gear, relevant parts shall be cleaned as much as possible before installation. In order to avoid the fault caused by the dirt entering the steering oil circuit, the plug on each oil port of steering pump of steering gear shall be opened before connecting the oil pipe, and the oil pipe and plug shall be carefully cleaned and deburred.

Turn the steering wheel to the straight ahead position. Clean the mounting bracket of the steering gear and relevant mating surfaces of the steering gear. For the adjustable steering column, use a suitable rope to pass through the space of the cross fork of the steering shaft, hang the steering shaft, and connect the steering shaft and the input shaft of the steering gear. Turn the steering gear to the middle position to align the relevant marks at the input end and output end of the steering gear.

Install the steering gear on the mounting base and tighten the fixing bolts. Universal joint or coupling between mounting column and steering gear.

For the adjustable steering column, the upper end seal of the steering gear shall not be damaged when the universal joint is installed. Keep the steering wheel in straight ahead position.

Put the pitman arm on the steering gear to align the two marks. Tighten the locknut according to the specified torque and rivet (anti loose pit). How to Replace a Power Steering Rack. Drain the power steering fluid, loosen the front wheel nuts and jack up the car.

Once the vehicle is properly supported on the jack stands, remove the front wheel lug nuts and the wheels. Detach the clamps connecting the steering column to the piston. Disconnect the outer rod ends using a special tie rod separator or ball joint fork. Loosen the nuts and turn the rods. Remove the faulty steering rack.

Insert a drainage pan under the car to catch any fluid and unbolt the power steering rack from its seating. Remove the rack via one of the wheel wells. Use plenty of effort, patience and ingenuity.

Install the new power steering rack. Using the same exit point as your entry point, insert the replacement rack into position using the required force. Measure the length of the old rack to determine the precise positions of the tie and cotter pins.

Insert the pins in the new rack. Reattach the hoses, except the steering fluid reservoir return line. Replace the components that were removed to enable access to the rack, together with the front wheels. Bleed the power steering system.

Turn the steering wheel back and forth for about 15 minutes to release air trapped in the system. Turn off the engine and let it stand before topping up the reservoir with fluid. If the fluid is light brown in colour or has foam on the top, repeat the process until the fluid is clear. Reattach the reservoir hose, remove the drainage pan, lower the car and tighten the wheel nuts.

Before Placing an Order, Be Sure to Check the Compatibility and Confirm That This Part Is Suitable for Your Vehicle. To Confirm, Please Select a Vehicle from the "My Garage" List or Enter Your Vehicle Details Above to Ensure That Your Model Is Included in the Compatibility Table. If You Encounter the Problem That You Can't Confirm Whether the Model Is Suitable, Please Contact Me.

I Can Quickly Answer the Adaptability Problem for You. Thank You for Your Cooperation and Support!

Please Check the Manul of Your Vechicle and Choose the Correct Good. If You Are Not Sure the Which Socket Your Vehicle Need.

Please Send Us Your Car Make, Model, Year and Other Information, We Will Help to Check Which You Need. Dear my friend, we appreciate your support. And our goal is service you well and give you a pleasant shopping time in our store. 2: Send pictures: outer packaging&scanned labels&item itself&with complete accessories, etc.

Rule A: The original packaging of the item is in an unused state. Rule B: The outer packaging must not have any damage. 2: Find a better price.

Missing accessories/quality issues/transportation damage, etc. Thank you very much for your understanding.

I hope we have a pleasant cooperation! Feedback could not solve anything, communication Please! (NO) Three stars is LOW star, NO 1,2,3 stars PLEASE! (YES) Please give us Five-star! Step 3: Describe your question clearly; we will give you the best solution.

Feedback is very important to us. If we don't understand these problems, we won't be able to solve them! After understanding the problem, we will be able to give you a satisfactory answer! Your comment is very important in our business success.

Rack and Pinion Assembly fits Honda Ridgeline 2006 - 2014 26-2726. Power Steering Rack and Pinion for Toyota RAV4 1996 - 2000 L4 2.0L Complete. For 2003 - 2006 Mitsubishi Outlander 2.4L Power Steering Rack Pinion Assembly US. Power Steering Rack and Pinion for 2006 2007 2008 Ford F-150 Lincoln Mark LT 4WD.

Power Steering Rack And Pinion For Nissan Quest 2004 2005 2006 2007 2008 2009. Power Steering Rack & Pinion For Chrysler Daytona LeBaron Shadow Spirit 22-320.