Complete Power Steering Rack And Pinion For Acura Tsx 2004 2008 All Models

Complete Power Steering Rack And Pinion For Acura Tsx 2004 2008 All Models
Complete Power Steering Rack And Pinion For Acura Tsx 2004 2008 All Models
Complete Power Steering Rack And Pinion For Acura Tsx 2004 2008 All Models
Complete Power Steering Rack And Pinion For Acura Tsx 2004 2008 All Models
Complete Power Steering Rack And Pinion For Acura Tsx 2004 2008 All Models
Complete Power Steering Rack And Pinion For Acura Tsx 2004 2008 All Models
Complete Power Steering Rack And Pinion For Acura Tsx 2004 2008 All Models
Complete Power Steering Rack And Pinion For Acura Tsx 2004 2008 All Models

Complete Power Steering Rack And Pinion For Acura Tsx 2004 2008 All Models
Part: Steering Rack and Pinion. Surface Finish: Polished, Rust Protected. Placement on Vehicle: Front Unit Left Right. Interchange Part Number: 26-2703 Hydraulic Steer For Front Unit Left Right, Acura TL Honda Accord, coupe hybrid ex lx dx ex-r se 2.4l 3.0l, 2003 2004 2005 2006 2007 honda accord, steering gear. Complete Power Steering Rack And Pinion For Acura Tsx 2004 - 2008 All Models. Compatible with the following vehicles. Removing and reinstalling a rack-and-pinion steering system is the same procedure for most vehicles. The only difference is the way it is removed from the frame.

In some vehicles, you must lower the subframe to take the system out, while steering racks on other vehicles are located below the frame, and the subframe does not need to be altered. Follow these directions for cars with a steering rack located below the subframe. Set the front tires forward using the steering wheel and lock the steering in place to keep the tires in alignment.

Then remove both the positive and negative cables from the car battery. Use a jack and jack stands to elevate the car and remove the front wheels. Drain the power steering fluid and detach the steering column lower joint.

Remove all nuts from the inner and outer tie rods, and disconnect the tie rod ends from the steering knuckles. Detach the front exhaust tube and place a support below the engine.

Remove the center member and all nuts attached to the engine mounts. Remove all nuts from the bulkhead hole cover and move the cover aside. Take the lower joint off the rack and pinion. Remember the steering neutral position by making a mark on the pinion housing and shaft. Detach the power steering fluid pipes and mounting bracket bolts, and then remove the rack and pinion altogether.

Guide the new rack and pinion into position and replace the mounting brackets. Tighten the nuts to 54-72 foot-pounds of torque. Connect the power steering fluid pipes to the rack and pinion. The lower pressure line should be torqued to 20-29 foot-pounds and the higher pressure line should be torqued to 11-18 foot-pounds. Align the lower steering joint and pinion shaft, and torque to 17-22 foot-pounds.

Replace the bulkhead hole cover and tighten to 36-43 inch-pounds. Place the engine mounting center member back into position, tightening all bolts to 57-72 foot-pounds. Then take the support out from below the engine. Tighten the nuts on the tie rod ends to 22-29 foot-pounds and secure a new cotter pin in place.

Install all other objects in the opposite order of their removal. Fill the power steering reservoir with fluid, and then bleed the system. Perform a four-wheel alignment if needed.

Rack & Pinion Complete Unit;Steering Rack;Steering Gear. Backed by satisfying after-sales service. Rotate quickly and normal position.

Rack replacement kit, rack and pinion, power rack parts. Power Steering Rack;Steering Rack and Pinion. Rack and Pinion Assembly, Rack and Pinion Rack Gear. Top performance For long service life. International Buyers C Please Note. These charges are the buyers responsibility. Q: How do I return an item? Please contact our customer service before you return an item. If you are dissatisfied for any reason, please do not be quick to leave negative/neutral feedback. UTV & ATV Brake System Parts. Nerf Bars & Running Boards. Wheel Stem Air Valve Cap.

Splash Guards & Mud Flaps. 4 pcs wheel hub bearing. Car Window Film Tint Tools. For Ford F-150 Expedition 5.4L 4.6L Explorer Lincoln DG508 Ignition Coil 8 Pack.

2x Front Hood Gas Lift Supports Struts Shocks Springs For Dodge Ram 02-10 4364. Pair (2) Front Or Rear Wheel Hub Bearing Fits Chevy Impala Buick LeSabre Venture. 2 X Front/Rear Wheel Hub Bearing For Buick LaCrosse Century Chevy Impala Venture. 2x Front Hood Lift Supports Shocks Struts For Dodge Ram 1500 2500 3500 4500 5500. 2pcs for 2011 Buick LaCrosse 3.6L Upstream Downstream Oxygen Sensor O2 02. Fits 04-09 Toyota Sienna Acrylic Window Visors 4Pc Set. For Chevy GMC Suburban C/K Tahoe Yukon Foldable Power Side View Mirrors Pair Set. 2pcs Front Lower Control Arm Suspension For 2004 2005 2006 2007 Suzuki Aerio. The item "Complete Power Steering Rack And Pinion For Acura Tsx 2004 2008 All Models" is in sale since Friday, May 10, 2019. This item is in the category "eBay Motors\Parts & Accessories\Car & Truck Parts & Accessories\Steering & Suspension\Gearboxes, Rack & Pinions". The seller is "topcn-autoparts" and is located in Ontario, California.

This item can be shipped to United States.


Complete Power Steering Rack And Pinion For Acura Tsx 2004 2008 All Models